Repurposed plastic balls into flowers
Check out how easy it is to create fun and colorful flowers with repurposed plastic balls, which are used in bouncy castles.
When I created some diy plastic flowers a while back, out of thrifted plastic balls, I said I would play around with what I had left and see what other flowers I could make.
Well, I had some fun and did just that.
And these larger flowers are so easy to create.
I found a couple of bags of these plastic balls that are used in bouncy castles at a thrift store quite a while back for a dollar a bag.
Colorful things like these balls always catch my eye.
Creating repurposed plastic ball flowers
To create these flowers start by simply poking a hole into a ball with a pair of scissors.
Then cut about three quarters the way down the side of the ball until you have it in quarters.
Be careful not to cut all the way down.
Then cut down the middle of the four sections until you have eight sections.
Now it’s time to invert the ball and see the beginnings of your flower.
Now you have a flower with eight petals.
You could work with it like this, or continue like I did.
And cut down the middle of the eight petals, creating sixteen petals.
Here are all of my cut flowers. I have to work with the colors that I had.
To create different sized flowers you just trim the petal ends until you get the length that you want.
The three little flowers are made from half a ball.
Once you have your flowers ready it’s completely up to you what you do with them.
You could create flowers that are all one color.
Or mix the colors.
There’s really no wrong here, you can stack the layers any way you like.
I decided I wanted my flowers to be varying shades of the same color, and the easiest way to do that is with spray paint.
Spray painting repurposed plastic ball flowers
I spray painted the fronts of these flowers with three different shades of aqua blue, using a paint and primer combo spray paint.
Three light coats did the trick.
There are several spray paint brands that have paint and primer combos, just make sure that plastic is listed as a material that the paint can be used for.
Then I did the same to the backs.
I went on to create a flower with pinks, and another with purples.
When my flowers were done I glued the stacked layers together using my glue gun, alternating each flower layer in a way that looked good to me.
It’s important to make sure to get good contact with each layer. If you don’t, it might be that middle area of the one on top isn’t sitting flat on the middle area of the one below.
If that happens, you just need to snip into the middle of the top flower layer a little more to make the middle area a little flatter.
To finish off my diy flowers I glued on pretty pearlescent buttons, but there are so many things that could be used.
Because I used hot glue these flowers are for inside only.
Now that my repurposed plastic ball flowers are done it’s time to do something fun with them.
I’m using mine in a wall display, but you could use yours any way you like.
These flowers are about six inches across so they do make a nice statement.
Because I’m using what I already have I glued the flowers onto the ends of some wooden rulers.
And then I glued the rulers in place inside a wall planter thingy on this barn board frame that I’ve had around for a long time.
After I did this I decided to tie the rulers to the chicken wire frame with some jute twine. I did this just under the flowers so it can’t be seen.
If I had thought of that I would have tied the rulers in place first and then glued the flowers onto the rulers, but it still worked out fine.
I love the contrast of the barn board frame, and the chicken wire and burlap, with the spray painted plastic flowers.
Here are my repurposed plastic ball flowers displayed in my living room beside my no sew repurposed scarf curtains.
I moved my decoupaged wicker plates upstairs to the master bedroom. I do like to move things around to keep my decor interesting and fun.
These flowers are pretty easy to make, and because you can spray paint them they can be customized to any color combos that you love.
Supplies needed for this project
- plastic bouncy castle balls
- spray paints
- glue gun
- glue sticks
Please pin to your favorite board.
Thanks so much for reading, and until next time,